Mackie Onyx Artist 1x2 vs Audient iD24 compared — specs, features, and which one to buy for your setup. See the full breakdown on CreatorConfig.
The Ruling
The Audient iD24 wins Mic Inputs, Monitoring, Creator Features and Connectivity. It is the pricier of the two at $399, so the Mackie Onyx Artist 1x2 stays the pick if $200 matters more than those specs.
Unless…
At a Glance
Every axis is scored out of 10 from the catalog specs below. The scores are relative to the products on this page, so a 10 means “best of these”, not “perfect”, and two identical columns mean the catalog genuinely cannot separate them. Axes the catalog holds no figure for on both sides are left off entirely rather than guessed at.
| Category | Mackie Onyx Artist 1x2 | Audient iD24 |
|---|---|---|
| Audio Resolution | 10/10 | 7.5/10 |
| Mic Inputs | 5/10 | 10/10 |
| Monitoring | 7.5/10 | 10/10 |
| Creator Features | 0/10 | 10/10 |
| Connectivity | 5/10 | 10/10 |
| Power | 10/10 | 10/10 |
The Split
Desktop audio interface intended for creator workflows, microphone input, monitoring, and clean signal routing.
On paper the Mackie Onyx Artist 1x2 takes sample rate (192kHz, +96kHz). It gives up loopback and ADAT expansion to the Audient iD24. It is the cheaper of the two, by $200.00.
Leads on
Higher sample rates capture more audio detail — important for professional recording and mixing.
Pro-level USB-C audio interface with strong preamps, monitor control, and expandable I/O.
On paper the Audient iD24 takes loopback (Yes), ADAT expansion (Yes), XLR inputs (2, +1) and headphone outputs (2, +1). It also leads on TRS outputs. It gives up sample rate to the Mackie Onyx Artist 1x2. That costs $200.00 more than the Mackie Onyx Artist 1x2.
Leads on
Loopback routes computer audio back into the stream without a second interface or cable.
ADAT lets you add eight more inputs later instead of replacing the interface.
More XLR inputs let you record multiple microphones simultaneously.
A second headphone output lets a guest monitor without a splitter.
More TRS outputs allow routing to studio monitors and outboard gear.
These 6 specs are the same on both of them, so none of it is part of the decision.
The Record
A group is won by whoever takes more of its rows outright. Specs the catalog cannot rank are shown but never decide a group.
Bottom Line
The Audient iD24 is the pick on the specs the catalog holds, but “better on paper” and “right for you” are different questions. Each case below names what the product is actually good at and who that suits.
The clearest difference is loopback, which the Audient iD24 has and the Mackie Onyx Artist 1x2 does not. Across the catalog's specification sheet the two differ on 6 specs. They match on 6 specs, including connection type, bit depth and phantom power. Two audio interfaces from Mackie and Audient, each taking a different approach to audio quality and I/O flexibility.
Get the Audient iD24. The Audient iD24 wins Mic Inputs, Monitoring, Creator Features and Connectivity. It is the pricier of the two at $399, so the Mackie Onyx Artist 1x2 stays the pick if $200 matters more than those specs.
Both share 6 specifications in the catalog, including connection type (usb-c, xlr, trs), bit depth (24-bit), phantom power (Yes) and direct monitoring (Yes), among others. None of those is a reason to pick one over the other.
The Audient iD24 costs $399.00 against $199.00, a difference of $200. The premium buys loopback (Yes), ADAT expansion (Yes) and XLR inputs (2). Whether that is worth it depends on which of those you would actually use.